Changing bindings

This is the World Famous TelemarkTalk / TelemarkTips Forum, by far the most dynamic telemark and backcountry skiing discussion board on the world wide web. We have fun here, come on in and be a part of it.
Post Reply
User avatar
Jasonsansfleece
Posts: 7
Joined: Mon Nov 21, 2022 12:08 pm

Changing bindings

Post by Jasonsansfleece » Fri Nov 25, 2022 9:32 pm

Is it OK to change bindings on a ski? Say you have a BC binding and you wanted to change it to a 75 mm three pin binding. I imagine there would be a different hole pattern, extra holes etc. Possible, permissible?

User avatar
Mtnbbud
Posts: 11
Joined: Sun Nov 20, 2022 7:58 pm
Location: Willamette Valley
Ski style: Backcountry
Favorite Skis: Outtabounds
Favorite boots: T4's
Occupation: Semiretired

Re: Changing bindings

Post by Mtnbbud » Fri Nov 25, 2022 11:53 pm

I'm far from an expert, but I just did the same with a pair of skis I picked up for next to nothing. You will more than likely need new holes - the holes from the BC binding will likely be in the wrong position. You will need to fill in the old holes. I'm not going to tell you where to drill your new holes, because I'd hate to tell you wrong. I couldn't get ahold of a drill template for my bindings so I got my advice for positioning the holes from a REI ski shop. If you can get ahold of a template for your bindings, it might relieve some of the guess work. Either way, you'll need to find the balance point on your skis if its not already marked. I'll let others with more experience chime in on what to do. Good luck!



User avatar
John Dee
Posts: 274
Joined: Sat Sep 25, 2021 8:15 pm

Re: Changing bindings

Post by John Dee » Sat Nov 26, 2022 12:09 am

The hole pattern is the same, but the balance point is different.



User avatar
Montana St Alum
Posts: 1205
Joined: Thu Oct 22, 2020 6:42 pm
Location: Wasatch, Utah
Ski style: Old dog, new school
Favorite Skis: Blizzard Rustler 9/10
Favorite boots: Tx Pro
Occupation: Retired, unemployable

Re: Changing bindings

Post by Montana St Alum » Sat Nov 26, 2022 11:47 am

You can hammer in golf tees into wood glue in the old holes. If the new holes are more than a couple of CM from the old holes, I'd imagine the connection would be secure. Ask at a shop or use inserts in epoxy to be more secure.

You can usually download a template to overlay to see what you're working with as far as new position.



User avatar
JohnSKepler
Posts: 562
Joined: Thu Sep 08, 2022 6:31 pm
Location: Utahoming
Ski style: XCBCD
Favorite Skis: Voile Objective BC, Rossignol BC 80
Favorite boots: Scarpa F1 Bellows, Alpina Alaska XP
Occupation: Rocket Scientist

Re: Changing bindings

Post by JohnSKepler » Sat Nov 26, 2022 12:25 pm

I've heard that it is best to not put a new hole within 1 centimeter of an old hole. I agree with @Montana St Alum on the inserts. You can also get them here if you want to do it yourself: https://www.bindingfreedom.com/

If you hammer golf tees into a hole filled with wood glue, use Titebond III or another waterPROOF glue. Snow melts into water and if it isn't waterPROOF...
Last edited by JohnSKepler on Sat Nov 26, 2022 1:09 pm, edited 1 time in total.
Veni, Vidi, Viski



User avatar
Montana St Alum
Posts: 1205
Joined: Thu Oct 22, 2020 6:42 pm
Location: Wasatch, Utah
Ski style: Old dog, new school
Favorite Skis: Blizzard Rustler 9/10
Favorite boots: Tx Pro
Occupation: Retired, unemployable

Re: Changing bindings

Post by Montana St Alum » Sat Nov 26, 2022 12:41 pm

JohnSKepler wrote:
Sat Nov 26, 2022 12:25 pm
I've heard that it is best to not put a new hole within 1 centimeter of an old hole. I agree with @Montana St Alum on the inserts. You can also get them here if you want to do it yourself: https://www.bindingfreedom.com/
Yeah 1cm+ sounds more accurate.



Post Reply