Fixing Tear In a Lightweight Waterproof Shell

This is the World Famous TelemarkTalk / TelemarkTips Forum, by far the most dynamic telemark and backcountry skiing discussion board on the world wide web. We have fun here, come on in and be a part of it.
Post Reply
User avatar
JohnSKepler
Posts: 559
Joined: Thu Sep 08, 2022 6:31 pm
Location: Utahoming
Ski style: XCBCD
Favorite Skis: Voile Objective BC, Rossignol BC 80
Favorite boots: Scarpa F1 Bellows, Alpina Alaska XP
Occupation: Rocket Scientist

Fixing Tear In a Lightweight Waterproof Shell

Post by JohnSKepler » Fri Oct 13, 2023 6:36 pm

I have a nice, Rab lightweight shell I often carry on Telemark outings. I was going through gear recently and discovered about a 1" tear in the sleeve a few inches above the cuff. It's nice and straight without any fraying.

Any recommendations on repairing it? I've used the repair tape on smaller tears but this tear is longer than the recommended size on the tape and I'm not out on the trail needing an emergency repair. It's a nice shell that I'd like to keep using as long as I can.

Thanks!
Veni, Vidi, Viski

User avatar
spopepro
Posts: 260
Joined: Fri Feb 07, 2020 2:15 pm

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by spopepro » Fri Oct 13, 2023 6:47 pm

I’ve had good luck with noso patches. My wife’s hardshell pants are almost more patch than pants as she keeps catching her crampon points. :/
Last edited by spopepro on Sat Oct 14, 2023 8:49 pm, edited 1 time in total.



User avatar
skimrg
Posts: 8
Joined: Fri Oct 13, 2023 3:53 pm

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by skimrg » Sat Oct 14, 2023 6:37 pm

GoreTex Patch - outside or inside

like this "GEAR AID Tenacious Tape GORE-TEX Fabric Patches for Jacket Repair, Black, Round and Rectangle" from am-zon.



mca80
Posts: 994
Joined: Sun Jan 02, 2022 5:24 pm
Location: Da UP eh
Ski style: Over the river and through the woods
Favorite Skis: Nansen, Finnmark, Kongsvold, Combat NATO, Fischer Superlite, RCS
Favorite boots: Crispi Bre, Hook, Alpina 1600, Alico Ski March, Crispi Mountain

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by mca80 » Sat Oct 14, 2023 7:47 pm

If it's not in a spot that gets frequent bending stress I can't see how any patch or tape whatsoever would not work. I have, and have seen, tents and other items with tape and patches all over without any ill effect. Heck even duct tape would be fine although perhaps not your wife's aesthetic.



User avatar
phoenix
Posts: 861
Joined: Mon Jan 02, 2017 5:44 pm
Location: Northern VT
Ski style: My own
Favorite Skis: Varies,I've had many favorites
Favorite boots: Excursions, T1's
Occupation: I'm occupied

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by phoenix » Sun Oct 15, 2023 3:45 pm

I'd use the nylon patches if you have them. Round the corners of the patch (so an oval or round shape). Stick a piece of cardboard behind the tear, smooth the area to patch, and apply it smooth and firmly. Then give it just a bit of heat from a hair dryer, and press again.
You can double it with a matching patch on the inside, but not necessary.

I've done a single patch on a couple of jackets and they've lasted years, if applied well. In particular, had a patch on a light wind jacket that survived many years of very hard use. I think the patch was still there when I retired the jacket due to it's general falling apart.



User avatar
Shintangle
Posts: 9
Joined: Sun Dec 29, 2013 9:27 pm

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by Shintangle » Sun Oct 15, 2023 6:28 pm

I have had good results with McNett Seam Grip. On the outside of the garment line up both sides of the tear and put some masking tape to hold it in place. Then apply the Seam Grip on the inside side of the tear. Once the Seam Grip has cured remove the masking tape from the outside. If done well the tear will be almost invisible.



User avatar
JohnSKepler
Posts: 559
Joined: Thu Sep 08, 2022 6:31 pm
Location: Utahoming
Ski style: XCBCD
Favorite Skis: Voile Objective BC, Rossignol BC 80
Favorite boots: Scarpa F1 Bellows, Alpina Alaska XP
Occupation: Rocket Scientist

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by JohnSKepler » Mon Oct 16, 2023 11:37 am

Shintangle wrote:
Sun Oct 15, 2023 6:28 pm
I have had good results with McNett Seam Grip. On the outside of the garment line up both sides of the tear and put some masking tape to hold it in place. Then apply the Seam Grip on the inside side of the tear. Once the Seam Grip has cured remove the masking tape from the outside. If done well the tear will be almost invisible.
How long of a tear have you repaired this way? This tear is an "L" with each part being about 3/4" which is why I don't want to try to use a patch, it'll be a big patch. It is in a fairly low-stress spot on the jacked out on the arm a few inches up from the cuff on the side facing inward. I have absolutely no idea how this happened. Looks like someone took scissors to the darn thing!

Is this the stuff? There are several related products but this looks closest to what you recommended.

https://www.gearaid.com/products/seam-g ... 8044147153

I wonder if I could use this for a small puncture in a Camelbak bladder? I've got some vinyl glue that 'works' but I've had to do it twice and it's leaking again.
Veni, Vidi, Viski



User avatar
Manney
needs to take stock of his life
needs to take stock of his life
Posts: 991
Joined: Tue Mar 07, 2023 8:37 am

Re: Fixing Tear In a Lightweight Waterproof Shell

Post by Manney » Mon Oct 16, 2023 12:19 pm

Don’t risk poisoning yourself (3rd time is a charm?). Buy a new Camelbak bladder. They need to be replaced as a matter of course anyway.

BTW, Rab has a repair service.
Go Ski



Post Reply